kradcliffe
Noticed this a few times now, happens maybe 2 or 3 times per gig randomly.
Have FX part select on vocal then when loading a new track the vocal in the track will be slightly off from the rest of the track without the FX active. Pressing the vocal button off sorts it instantly.
Doesn't matter where the FX select switch is set to and it seems to happen just on the right deck.
Have FX part select on vocal then when loading a new track the vocal in the track will be slightly off from the rest of the track without the FX active. Pressing the vocal button off sorts it instantly.
Doesn't matter where the FX select switch is set to and it seems to happen just on the right deck.
Posted Sun 17 Nov 24 @ 12:58 am
djdad
You have the setting resetFxOnLoad to Yes ?
When this happens again, can you check if any FX is active on Deck 2 (check the FX Drop-down List and see if there is "on/green" switch turned on)
Any particular type of Track loaded on a Deck ?
You have Stems to always/on ?
When this happens again, can you check if any FX is active on Deck 2 (check the FX Drop-down List and see if there is "on/green" switch turned on)
Any particular type of Track loaded on a Deck ?
You have Stems to always/on ?
Posted Sun 17 Nov 24 @ 12:55 pm
kradcliffe
Yes FX resets on deck load. Will check the FX to see if active next time it happens.
Just random tracks, maybe 2 / 3 times a gig.
Stems are set to fully disabled but using precomputed files on the hard drive as the laptop isn't powerful enough to process them in realtime.
Just random tracks, maybe 2 / 3 times a gig.
Stems are set to fully disabled but using precomputed files on the hard drive as the laptop isn't powerful enough to process them in realtime.
Posted Sun 17 Nov 24 @ 1:00 pm
kradcliffe
Hi Babis,
I did some more playing about with the FLX10 last night and noticed another related thing. This didn't happen straight away, but maybe 10 minutes in to my session I noticed the track I was playing went a bit "mushy" (like low bitrate) if any of the FX Part buttons were lit. Push the buttons off so no FX part selected and the sound went clear again. This happens on both decks. Also noticed if I use the cut effect on a particular deck the vocals go mushy when it's active then go back to normal when it's deactivated.
Can't actually figure out what causes this to happen but that's two nights in a row I've noticed it and using two different PCs.
I checked and there are no FX active on either deck or the master. This is probably related to the similar issue where the vocals become detached from the rest of the track.
I also noticed if I have filter active on a deck by pressing a FX part button it cuts the filter off and introduces drums, vocals etc. Surely this shouldn't happen to the master output of the FX part is not active on a deck or master?
I did some more playing about with the FLX10 last night and noticed another related thing. This didn't happen straight away, but maybe 10 minutes in to my session I noticed the track I was playing went a bit "mushy" (like low bitrate) if any of the FX Part buttons were lit. Push the buttons off so no FX part selected and the sound went clear again. This happens on both decks. Also noticed if I use the cut effect on a particular deck the vocals go mushy when it's active then go back to normal when it's deactivated.
Can't actually figure out what causes this to happen but that's two nights in a row I've noticed it and using two different PCs.
I checked and there are no FX active on either deck or the master. This is probably related to the similar issue where the vocals become detached from the rest of the track.
I also noticed if I have filter active on a deck by pressing a FX part button it cuts the filter off and introduces drums, vocals etc. Surely this shouldn't happen to the master output of the FX part is not active on a deck or master?
Posted Mon 25 Nov 24 @ 6:50 pm
kradcliffe
Did anyone get a chance to look at this? Planning to use the FLX10 on Friday so just wanted to check if anything has been found. Thanks.
Posted Tue 26 Nov 24 @ 10:20 pm
kradcliffe
OK just dug out the FLX10 again and it's still happening but only sometimes and not deck specific.
If I load a track on a deck and FX part select is vocals and the Beat FX is set for that deck (but nothing active) the vocals of the track aren't aligned with the other parts (slightly out) however if I click the FX part vocal button is instantly sorts it.
Its as though the track is using the stems vocal with no need for it as no stems effect is active.
If I load a track on a deck and FX part select is vocals and the Beat FX is set for that deck (but nothing active) the vocals of the track aren't aligned with the other parts (slightly out) however if I click the FX part vocal button is instantly sorts it.
Its as though the track is using the stems vocal with no need for it as no stems effect is active.
Posted Tue 18 Feb 25 @ 3:32 pm
Adion
Did you have an effect active before it happens?
Also, are you using prepared stems?
Also, are you using prepared stems?
Posted Tue 18 Feb 25 @ 5:07 pm
kradcliffe
I had been using the stems effects on previous tracks, so maybe it gets locked on somehow.
Stems are pre-prepared and saved so not computed in real time.
Stems are pre-prepared and saved so not computed in real time.
Posted Tue 18 Feb 25 @ 5:13 pm
Adion
Which effects did you use?
Posted Tue 18 Feb 25 @ 5:21 pm
kradcliffe
I've noticed it when the cut effect is selected and vocal stem FX only.
Posted Tue 18 Feb 25 @ 5:26 pm